Influence of silicon on the microstructure and mechanical properties of Zr-Si-N composite films

A series of Zr-Si-N composite films with different Si contents were synthesized in an Ar and N₂ mixture atmosphere by the bi-target reactive magnetron sputtering method. These films’ composition, microstructure and mechanical properties were characterized by energy dispersive spectroscopy, X-ray diffraction, scanning electron microscopy, atomic force microscopy and nanoindentation. Experimental results revealed that after the addition of silicon, Si₃N₄ interfacial phase formed on the surface of ZrN grains and prevented them from growing up. Zr-Si-N composite films were strengthened at low Si content with the hardness and elastic modulus reaching their maximum values of 29.8 and 352 GPa at 6.2 at% Si, respectively. With a further increase of Si content, the crystalline Zr-Si-N films gradually transformed into amorphous, accompanied with a remarkable fall of films’ mechanical properties. This limited enhancement of mechanical properties in the Zr-Si-N films may be due to the low wettability of Si₃N₄ on the surface of ZrN grains.     

离化团簇束法制备c轴取向的ZnO薄膜

为了探索低温可调控ZnO薄膜沉积技术,提出了一种新的ZnO薄膜制备方法,即离化团簇束（ICB）法,并自行设计研制了应用该方法制备ZnO薄膜的专门装置.采用超音速喷嘴获得高速锌原子团簇束,用Hall等离子体源产生氧离子束离化锌原子团簇,获得了较高的离化率.在沉积过程中,可以通过调节衬底偏压、氩氧比、衬底加热温度等参数,来控制成膜的质量;应用这个装置成功地在硅衬底上制备的ZnO薄膜,经XRD和EDS检测,薄膜的c轴取向一致,Zn、O原子百分比接近于1：1,成膜质量好.     

Phosphonate electrochemical recognition by molecularly imprinted deposited film

In this paper, thin films of titanium oxide imprinted with O,O-dimethyl-(2,4-dichlorophenoxyacetoxyl)(3′-nitrobenyl) methinephosphonate (Phi-NO₂) were prepared via liquid phase deposition (LPD) method on a glassy carbon electrode. The imprinted molecular in the films was removed by treatment with immersion in CH₂Cl₂. X-ray diffraction (XRD) and electrochemical methods were introduced to show the evidence of the molecular imprinting phenomenon. It was also found that the recognition ability of the sensor depended on the substituents associated with tridimensional structures of the nitro-compounds. Under the optimized condition, the sensor showed better sensitivity, selectivity and reproducibility to the imprinted molecule and the linear relationship between the current and the concentration of analyte in the range of 0.1-50 μM was obtained. LPD proved to be a powerful method for imprinting titanium oxide thin sense films.     

An Extension Landau-Lifshitz Model in Studying Soft Ferromagnetic Films

In this paper, we propose a model in studying soft ferromagnetic films, which is readily accessible experimentally. By using penalty approximation and compensated compactness, we prove that the dynamical equation in thin film has a local weak solution. Moreover, the corresponding linear equation is also dealt with in great detail.     

用锌有机源和CO2/H2混合气源PECVD沉积ZnO薄膜

在等离子体作用下,以CO2/H2混合气为氧源,Zn(C2H5)2锌为锌源,在单晶硅上生长出高度择优取向的氧化锌薄膜。X射线衍射分析表明,薄膜为六方结构,c轴高度择优;原子力显微镜观察到晶粒是有规律地按六方排布,薄膜的表面粗糙度较小;从光致发光谱还发现在380 nm处有非常强的紫外峰。     

500.8 nmNd∶YAG青光激光器光学薄膜的设计与制备

从双波长激光运转及和频的机理出发，对LD泵浦Nd∶YAG，LBO腔内和频500.8 nm〖JP2〗青光激光器所使用的光学薄膜进行了设计和制备.在激光反射镜的设计上，为了达到最佳的和频输出，对膜系要求进行了深入分析.采用对谐振腔一端面反射率固定不变并通过对另一腔镜基频光的透射率进行调谐的方法, 在给出合理初始结构后，利用计算机对膜厚进行了优化.并采用双离子束溅射沉积的方法，通过时间监控膜厚法成功制备出青光激光器所使用的全介质激光反射膜, 在室温下实现946 nm和1064 nm双波长连续运转，并通过Ⅰ类临界相位匹配LBO晶体腔内和频在国内首次实现500.8 nm青色激光连续输出.当泵浦注入功率为1.4 W时和频青光最大输出达20 mW.     

单脉冲和多脉冲飞秒激光对单层光学薄膜的损伤

 利用掺钛的蓝宝石飞秒激光系统输出的单脉冲和多脉冲飞秒激光(中心波长800 nm，脉宽50 fs，靶面聚焦直径Ф 40 μm)，分别对BK7玻璃基底上厚约500 nm的单层HfO₂和单层ZrO₂薄膜进行辐照，得到了这两种薄膜在1-on-1和1 000-on-1测试方法下的激光损伤阈值。实验发现，两种方法下HfO₂单层膜的阈值均比ZrO₂单层膜的阈值高。从简化的Keldysh多光子离化理论出发，认为HfO₂薄膜材料的带比ZrO₂的宽是导致上述结果的主要原因。同时，同一种薄膜的多脉冲下的阈值比单脉冲下的低，原因是多脉冲下，飞秒激光对光学薄膜的损伤存在累积效应。     

p型未掺杂富锌ZnO薄膜的形成和性能研究

以高纯ZnO为靶材,氩气为溅射气体,利用射频磁控溅射技术在石英衬底上生长出纤锌矿结构的富锌ZnO薄膜.薄膜沿(002)择优取向生长,厚约为1.2μm,呈现电绝缘特性.将溅射的ZnO薄膜在10-3Pa,510~1 000 K的温度范围等温退火1 h,室温Hall测量结果表明ZnO薄膜的导电性能经历了由绝缘—n型—p型—n型半导体的变化.XPS测试表明ZnO薄膜的Zn/O离子比随退火温度的升高而降低,但一直是富锌ZnO,说明未掺杂的富锌ZnO也可以形成p型导电.p型未掺杂富锌ZnO薄膜的形成可归因于VZn受主浓度可以克服VO和Zni本征施主的补偿效应.     

磁控溅射ZnO薄膜的成核机制及表面形貌演化动力学研究

利用原子力显微镜分析了ZnO薄膜在具有本征氧化层的Si(100)和Si(111)基片上的表面形貌 随沉积时间的演化. 通过对薄膜生长形貌的动力学标度表征，研究了射频反应磁控溅射条件 下，ZnO薄膜的成核过程及生长动力学行为. 研究发现，ZnO在基片表面的成核过程可分为初 期成核阶段、低速率成核阶段和二次成核阶段. 对于Si(100)基片，三个成核阶段的生长指 数分别为β₁=1.04，β₂=0.25±0.01，β₃=0.74；对 于Si(11 关键词： ZnO薄膜 磁控溅射 生长动力学 成核机制     

短波通滤光片膜系设计

详细介绍用等效折射率概念设计短波通滤光片的原理和计算方法。根据原理和方法，选择二氧化钛（TiO2）作为高折射率材料、二氧化硅（SiO2）作为低折射率材料。首先从理论上计算出用这2种材料设计的波长λ=950～1150nm的短波通滤光片所需要的周期数，然后给出短波通滤光片的主膜系和光谱曲线。由于据此周期数设计出的膜系光谱曲线在750～810nm处的透过率不符合要求，因此对该膜系进行了改进。依照改进的设计进行多次制备，最终制备出了符合要求的短波通滤光片，找到了最佳制备工艺和方法。最后，对制备出来的短波通滤光片薄膜进行了各种环境实验。实验结果表明，膜层的各项指标符合设计要求。